The genuine Bosch cable that wires a rack-mounted PowerPack battery to the drive unit on an eBike System 2 (Classic+) bike. On those bikes the battery and the motor talk through this harness: one end clips into the rack-mounted battery tray, the other plugs into the drive unit, carrying both power and the system's data signal.
Available in-store and by order. Ask us and we’ll have it ready.

On an eBike System 2 bike with a rack-mounted PowerPack, this is the harness between the battery tray and the drive unit. It carries both the power and the data the motor and battery use to talk, so the system reads the right charge level and delivers assist.

A corroded pin or a fatigued strain point under the rack shows up as an intermittent battery dropout or a system error, not always a dead bike. If the fault follows the cable, replacing it is the fix, and it is far cheaper than chasing a battery or motor.
The 720, 820, and 1100 mm options exist because the routing distance from the rack tray to the drive unit differs by frame. Match the length that came off the bike; too short will not reach, too long leaves slack to chafe.
This is the rack-battery cable. A downtube (frame-mounted) PowerPack uses a different cable, the eShift setup uses a rack Y-cable, and Smart System bikes (2022+) have no serviceable battery cable. Confirm which one your bike needs before ordering.
It's a wear-and-replace part. The connectors live in the weather under the rack, so over years of riding, washing, and battery swaps a pin can corrode or a strain point can fatigue, and the symptom is usually an intermittent battery dropout or a system error rather than a dead bike.
Choose this when you're keeping an older Bosch Classic+ bike on the road and have traced a power fault to the cable, or when a rack battery was added or relocated and the run length changed. It comes in three lengths (720 mm, 820 mm, 1100 mm) because the right one depends on how far the cable has to route from the rack tray to the motor on your frame.
Match the length to what came off the bike, or bring the bike in and we'll measure the run and confirm the connector type before you order. This is the rack-battery cable specifically; frame-mounted (downtube) PowerPacks and the eShift Y-cable use different harnesses, and Smart System (2022+) bikes don't use a serviceable battery cable at all.
Specs come from the maker and can change. If one of these numbers matters to you, ask us and we’ll check the exact item.
Smart System and the prior generation do not interchange. Our Bosch reference is the same set of pages our service team works from.
Don’t see yours? Ask the team directly.
Bosch eBike System 2 (Classic+) bikes with a rack-mounted PowerPack and a BDU2XX or BDU3XX drive unit, which covers Active Line, Active Line Plus, Performance Line, and Performance Line CX motors from roughly 2014 on. It does not fit Smart System (2022+) bikes, which do not use a serviceable battery cable.
The length depends on how far the cable routes from the rack-mounted battery to the drive unit on your specific frame. The safest move is to match the length of the cable that came off the bike. If you are not sure, bring the bike in or email us, and we will measure the run and confirm before you order.
No. This is the rack-mounted PowerPack cable. A downtube (frame) PowerPack uses a different cable, and bikes with eShift use a separate rack Y-cable. We can confirm which harness your bike uses.
It can be. On these older systems an intermittent dropout or a battery/communication error often traces to a corroded connector or a damaged cable under the rack rather than the battery or motor itself. We can test it and tell you whether the cable is the fault before you replace a more expensive part.
Yes. Bosch eBike systems are built to tight tolerances and the cable carries a data signal as well as power, so a non-genuine cable can introduce connection faults or system errors. This is the OEM Bosch part. Email us to order, or bring the bike in and we will fit it.
Tell us the bike you ride; we’ll confirm the accessory works with your specific frame, motor, and mounting points before it ships.
What is on our shelves is ready to pick up or ship. If something needs to be ordered, we tell you up front, not after you pay.
Shop install, walk-in service, or a remote walkthrough, whatever it takes to get the accessory working on your bike.