What maintenance is required for disc brakes?
What hydraulic disc brakes need: pad and rotor wear intervals, when to bleed the fluid, and which fluid type your brakes use, for city and cargo bikes.
Nearly all our bikes come with hydraulic disc brakes. They work differently from the cable brakes on older road and mountain bikes. Cable brakes are simpler to service, but hydraulics give you more stopping power and stay more consistent over time.
Each hydraulic brake has 7 main parts. Here's what each one does and what to watch for.
1. Brake pads: There's no precise mileage interval, because a lot of things affect wear, but a safe rule of thumb is roughly every 2,000 miles for a non-cargo bike and every 1,200 miles for a cargo bike.
2. Brake fluid: Check, burp, or bleed the fluid whenever you replace pads or a rotor, or whenever the lever feels soft. Fluid breaks down over time and stops holding pressure as well.
You don't have to handle this at home, but knowing your fluid type helps when you bring the bike in. Tektro and Shimano use red mineral oil, Magura uses blue mineral oil, and SRAM and Hayes use DOT fluid of various types.
Important: don't go by word of mouth. If you're not sure which fluid is compatible, check with the manufacturer directly.
3. The rotor: This is the metal disc on each wheel that the pads and caliper squeeze to stop the bike, and keeping it in good shape is really important for consistent braking.
The main things that hurt it are contaminants like motor oil from a wet street, plus normal wear from the pads. Wear speeds up if the caliper is out of alignment and dragging. If you ride off-road, check the rotor periodically for rock and gravel damage.
When to replace: a step or lip on the surface means gouging. A purple iridescent surface where the pads contact is another sign it's time.
Warning
Check each manufacturer's guide for minimum rotor thickness in millimeters. Some rotors are rated for "resin pads only," and running metallic pads on them can cause early wear or failure, because metallic pads are a much harder material.
If the rotor has no lip or burned surface and is above the manufacturer's minimum thickness, you're fine to keep riding. Wipe it down with rubbing alcohol to clear grime or grit that could affect braking.
4. Brake lever (the master cylinder assembly): There are two parts, the lever blade you rest your fingers on and a piston inside the housing (the master cylinder). Pulling the blade pushes the piston, which compresses the fluid and turns your pull into hydraulic pressure.
If you drop the bike on its side, check the lever, because that's a common cause of a blown master cylinder seal, and sometimes a blown caliper seal too. A lever that suddenly feels soft means the brakes need service.
Most levers have a "free stroke" adjustment knob or screw to set the distance from grip to lever for different hand sizes. It can buy you a bit more stopping power in the short term, but it doesn't replace servicing the pads, rotor and fluid.
5. Brake caliper: It sits near the disc and mostly stays out of the way, and on a well-maintained bike it doesn't cause many problems. Seal leaks happen but they're uncommon. Calipers just need pad changes and realignment from time to time.
6. Brake hoses: When you squeeze the lever, the master cylinder pushes fluid through the hose to the caliper, where pistons press the pads against the rotor, and when you let go the hose depressurizes.
Hoses rarely cause problems, but handle them carefully. Don't yank them, and try not to snag them off-road or when you're loading the bike. When setting up a bike or a new brake, route the hoses so the bars turn fully left and right without resistance.
7. Seals, o-rings and hydraulic fittings: They're small and barely visible, but they hold the pressure inside the master cylinder, hose and caliper, and without them the system leaks and fails.
Older systems needed periodic overhauls with fresh seals, o-rings and fittings. Now the standard is to replace whichever part has the failed seal, whether that's the master cylinder, the hose or the caliper.
Still stuck, or is this about your own bike? The service team answers these all day.